# Dovecot Logging¶

Dovecot always logs a detailed error message if something goes wrong. If it doesn’t, it’s considered a bug and will be fixed. However, almost always the problem is that you’re looking at the wrong log file; error messages may be logged to a different file than informational messages.

By default Dovecot uses the syslog service with mail facility. Dovecot can also be configured to log to files directly.

## Log File Location¶

You can find the log file locations by running:

doveadm log find


## Last Errors¶

You can easily print the last 1000 error messages of a running Dovecot:

doveadm log errors


## Changing Log File Paths¶

If you don’t want to use syslog, you can make Dovecot log to files directly:

log_path = /var/log/dovecot.log
# If not set, use the value from log_path
info_log_path = /var/log/dovecot-info.log
# If not set, use the value from info_log_path
debug_log_path = /var/log/dovecot-debug.log


The warning and error messages go to the file specified by log_path, while informative messages goes to info_log_path and debug messages goes to debug_log_path.

## Syslog¶

You can change Dovecot’s syslog facility from syslog_facility setting. The syslog configuration is often in /etc/syslog.conf or /etc/rsyslog* files.

When using syslog, Dovecot uses 5 different logging levels:

• debug: Debug-level message.

• info: Informational messages.

• warning: Warnings that don’t cause an actual error, but are useful to know about.

• err: Non-fatal errors.

• crit: Fatal errors that cause the process to die.

Where exactly these messages are logged depends entirely on your syslog configuration. Often everything is logged to /var/log/mail.log or /var/log/maillog, and err and crit are logged to /var/log/mail.err. This is not necessarily true for your configuration though.

In an ideal configuration the errors would be logged to a separate file than non-errors. For example you could set syslog_facility=local5 and set:

local5.*        -/var/log/dovecot.log
local5.warning;local5.error;local5.crit -/var/log/dovecot-errors.log


Here all the Dovecot messages get logged into dovecot.log, while all the important error/warning messages get logged into dovecot-errors.log.

Sometimes syslog is configured to log all info level logging to /var/log/messages. You can disable such duplicates for mail by adding “;local5.none”. For example:

*.info;local2.none;authpriv.none;cron.none;local5.none /var/log/messages


## Syslog rate limiting¶

rsyslog is configured with flood control enabled by default. Since Dovecot can log a lot in some situations, especially with debug loggine enabled, this causes log messages to be lost.

The rate limiting should be disabled in /etc/rsyslog.conf:

\$SystemLogRateLimitInterval 0


## Rotating Logs¶

You can use logrotate to maintain the Dovecot log files so they don’t grow beyond a manageable size. Save the below scriptlet as /etc/logrotate.d/dovecot:

/var/log/dovecot.log {
weekly
rotate 4
missingok
notifempty
compress
delaycompress
sharedscripts
postrotate
doveadm log reopen
endscript
}


Note

doveadm is not working properly with SELinux (e.g. doveadm cannot read config file when called from logrotate context). SELinux safe postrotate alternative scriplet:

postrotate
kill -s 0 cat /var/run/dovecot/master.pid || kill -s USR1 cat /var/run/dovecot/master.pid
endscript


## Internal Errors¶

If IMAP or POP3 processes encounter some error, they don’t show the exact reason for clients. Instead they show:

Internal error occurred. Refer to server log for more information. [2006-01-07 22:35:11]


The point is that whenever anything unexpected happens, Dovecot doesn’t leak any extra information about it to clients. They don’t need it and they might try to exploit it in some ways, so the less they know the better.

The real error message is written to the error log file. The timestamp is meant for you to help you find it.

## Logging verbosity¶

There are several settings that control logging verbosity. By default they’re all disabled, but they may be useful for debugging.

• auth_verbose=yes enables logging all failed authentication attempts.

• auth_debug=yes enables all authentication debug logging (also enables auth_verbose). Passwords are logged as <hidden>.

• auth_debug_passwords=yes does everything that auth_debug=yes does, but it also removes password hiding (but only if you are not using PAM, since PAM errors aren’t written to Dovecot’s own logs).

• mail_debug=yes enables all kinds of mail related debug logging, such as showing where Dovecot is looking for mails.

• verbose_ssl=yes enables logging SSL errors and warnings. Even without this setting if connection is closed because of an SSL error, the error is logged as the disconnection reason.

• auth_verbose_passwords=no|plain|sha1 If authentication fails, this setting logs the used password. If you don’t really need to know what the password itself was, but are more interested in knowing if the user is simply trying to use the wrong password every single time or if it’s a brute force attack, you can set this to sha1 and only the SHA1 of the password is logged. That’s enough to know if the password is same or different between login attempts.

• log_debug Flexible debug logging configuration.